Our company logo

State

7 Reasons Why Your Garage Door Keypad Is Not Working | How to Reset It


Do you have problems with your garage door keypad? You're not alone! A faulty keypad can be a reason for your lockout and a bad day in general. Below, we’ll outline seven everyday causes of a garage door keypad not working and the solutions that can be applied. We will also give you a comprehensive guide on how you can reset your garage door keypad as soon as possible. Do not let a trivial problem be a reason to ruin your day—scroll down and learn how to solve the problem that will let you back into your garage. If you require the services of a professional Garage Door expert, then you can count on Up & Down Garage Doors for repairs!

Common Causes of Garage Door Keypad Malfunctions


Many homeowners with a garage door keypad experience the inconvenience when the keypad fails, and you cannot tell what went wrong. If your garage door keypad is blinking and won't open, here are some common causes to consider:
  • Dead Batteries: One of the common causes is dead or weak batteries. If the keypad beeps but does not open the door, then it is high time to check the battery.
  • Misaligned Keypad: If your keypad is not installed correctly or simply not aligned correctly, it can be a problem when it comes to its interaction with the garage door opener. Make sure it is well screwed and at the right angle.
  • Weather Conditions: Excessive heat or cold may cause your keypad to develop some problems of poor or no response when the buttons are pressed. Sudden changes in temperatures such as high heat or freezing temperatures might affect the circuitry inside the electronics. If this is a frequent occurrence, try moving the keypad to a less exposed location.
  • Wiring Issues: Wiring that is frayed or damaged may affect the conductivity of electrical signals, which control the interaction between the keypad and the opener. Check on the wiring to identify any signs of damage or loose connections on any of the wiring.
  • Interference: Radiation interference from other gadgets within proximity or other wireless gadgets also influences functionality. If you have any other devices close to your keypad that you use often, then try to relocate them across in an attempt to keep the keypad interference-free.
  • Obstructions: Provide garage door maintenance frequently. Closely observe the keypads for any form of interference that may be caused by anything like dirt on the keypad. A small obstruction is enough to disrupt its functioning.
  • Old Equipment: If your keypad is old or outdated, then this could just be the right time for it to be replaced. Through constant use, their wear and tear manifest, and this eventually leads to malfunction.
These are the common causes of your garage door keypad not working, and once you identify them, you will know which garage door repair service you need. For professional assistance, do not hesitate to call UAD. Our expert technicians are available round the clock.

Step-by-Step Guide to Resetting Your Garage Door Keypad


Actually, it may be pretty helpful to reset a garage door keypad, as it helps solve certain malfunctions and restore functionality. Follow these simple steps to reset it effectively:
  1. Locate the Reset Button: Nearly all keypads come with a reset button. This can be usually located at the back or in the battery compartment as a rule. Check your user manual to know where it is located in detail.
  2. Remove the Cover: Unscrew the keypad cover with the aid of the screwdriver taking care not to over-twist it. This will allow you to access the battery and the reset button.
  3. Disconnect the Power: In order to make the cleaning as effective as possible, the power supply to the garage door opener should be turned off. This may be done by either pulling the plug out of the socket or switching off the circuit breaker.
  4. Press the Reset Button: When the power is off, hold down the reset button for approximately 10-15 seconds. This erases any previous settings on the keypad and sets it back to its default position to be programmed again.
  5. Reconnect Power: Once you have released the reset button, reconnect the power to the garage door opener. Insert it back or switch the circuit breaker on.
  6. Reprogram the Keypad: The instructions for reprogramming are usually in your user manual on how to program your keypad. This usually requires the entry of a new code or activating a sequence of buttons for instance pressing a certain button.
  7. Test the Keypad: After reprogramming, try to open the door using the new code on the keypad to make sure that it controlling the operations of the garage door properly.
Following the above steps, you will be able to reset the garage door keypad and get back into the garage. If the problem persists, it is better to consult a professional for help.

Summing up


In summary, if your garage door keypad is not working, it could be due to several factors, such as dead batteries, misalignment, or electronic interference. Fortunately, you can often resolve the issue by following the steps on how to reset the garage door keypad. However, if these solutions don't fix the problem or you prefer professional assistance, Up & Down Garage Doors is here to help. Our experienced team can diagnose and repair any garage door issues, ensuring your system operates smoothly. Don’t hesitate — call Up & Down Garage Doors today for reliable service and peace of mind!

You may also like